Difference between revisions of "Xi8088 Version 2.0"
Numberformat (talk | contribs) |
Numberformat (talk | contribs) |
||
| Line 230: | Line 230: | ||
== Troubleshooting == | == Troubleshooting == | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 22:34, 21 June 2021
Introduction
Xi 8088 IBM PC/XT compatible processor board.
Contributions Welcome
If anyone reading this page is interested in contributing content please send me a text message at 3476042083 with your email address and I will send instructions on how to setup an account.
Features
- ISA board form factor
- Support of PS/2 keyboard and mouse
- Built-in real time clock with NVRAM
Board Layout
Click on any chip for more information. Most of the chips below lead to blank pages. I am looking for help in populating them with some info. I know datasheets are available however it would be nice to have a brief summary of each component and what is does overall on this board.
Post Assembly
Once you have your board assembled you can proceed with configuring the memory map. If you plan on using a VGA graphics card and the 128Kb BIOS Flash Chip then all the switches should be in the off position.
Memory Map
The 20 bit address bus of the 8088/86 allows 1 Mb of memory space with address range from 00000-FFFFF. During the design phase of the first IBM PC, engineers had to decide n the allocation of the 1-megabyte memory space to various sections of the PC. This memory allocation is called a memory map.
| Start Address | End Address | Size | Purpose | Comments | ||||||||||||||
| 0x00000h | 0x9FFFFh | 640 KiB | Base memory | |||||||||||||||
| 0xA0000h | 0xBFFFFh | 128 KiB | Display memory | |||||||||||||||
| 0xC0000h | 0xEFFFFh | 192 KiB | Upper memory blocks (UMB) and BIOS extension ROMs | Consists of six 32 KiB user configurable blocks, can be either mapped to SRAM (to be used as UMB) or used for BIOS extension ROMs
| ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 0xE0000h | 0xEFFFFh | 64 KiB | On-board BIOS extension ROM | This is the upper 64 KiB of the 192 KiB block seen above. System flash ROM can be mapped here, so it can be used for BIOS extensions
| ||||||||||||||
| 0xF0000h | 0xFFFFFh | 64 KiB | System BIOS | Currently BIOS uses only top 32 KiB of this space (0xF8000h - 0xFFFFFh). The other 32 KiB part is mapped to the flash ROM and can be used for BIOS extensions
|
| Position | Description |
| 8 | ON = Monochrome display (MDA)
OFF = Color display (CGA) |
Processor Bootstrap
When the processor starts up it will be looking at fixed memory location. The Intel CPU will be looking at address 0xF:FFF0 for the jump instruction that will tell the processor the location of the POST Entry Point typically this number will be (EA 5B E0). EA is the machine code for JMP FAR absolute 4 byte address specified in the argument. The F000:E05B is the address to jump to. Scrolling up in the window you will see that there is some BIOS code that starts at that point this is the POST entry point which starts with a B8 which is a MOV instruction.
See table below for these address locations. When burning the BIOS onto the FLASH chip make sure to set the offset from the beginning of the chip since the BIOS is only 32 KiB the offset when using a 128 KiB chip will be 0x18000 I used a TL866 II writer with the XGecu Pro software. You can verify that the last line displayed should begin with EA 5B and end with FC FF.
;------------------------------------------------------------------------- ; Fixed BIOS Entry Points ; Source: ; Intel(R) Platform Innovation Framework for EFI ; Compatibility Support Module Specification ; Section 5.2 ; ; Location Description ; -------- ----------- ; F000:E05B POST Entry Point ; F000:E2C3 NMI Entry Point ; F000:E401 HDD Parameter Table ; F000:E6F2 INT 19 Entry Point ; F000:E6F5 Configuration Data Table ; F000:E729 Baut Rate Generator Table ; F000:E739 INT 14 Entry Point ; F000:E82E INT 16 Entry Point ; F000:E987 INT 09 Entry Point ; F000:EC59 INT 13 (Floppy) Entry Point ; F000:EF57 INT 0E Entry Point ; F000:EFC7 Floppy Disk Controller Parameter Table ; F000:EFD2 INT 17 ; F000:F065 INT 10 (Video) Entry Point ; F000:F0A4 INT 1D MDA and CGA Video Parameter Table ; F000:F841 INT 12 Entry Point ; F000:F84D INT 11 Entry Point ; F000:F859 INT 15 Entry Point ; F000:FA6E Low 128 Characters of Graphic Video Font ; F000:FE6E INT 1A Entry Point ; F000:FEA5 INT 08 Entry Point ; F000:FF53 Dummy Interrupt Handler (IRET) ; F000:FF54 INT 05 (Print Screen) Entry Point ; F000:FFF0 Power-On Entry Point ; F000:FFF5 ROM Date in ASCII "MM/DD/YY" Format (8 Characters) ; F000:FFFE System Model (0xFC - AT, 0xFE - XT)